|
|
#61
31-03-2011, 09:10
|
||||
|
||||
still working on it...
i have next week off, hope to get some work done 
|
|
#62
01-04-2011, 17:38
|
||||
|
||||
|
more stuff bought;
innovate mtx-l wideband lambda controller  mk1 westy grill  16 pieces of 50x20cm damping mats to get the cabin nice and quiet  I wanted a silent exhaust for the RDW check, but stock mk1 caddy exhaust is only available in straw-size. Custom stainless is a bit too expensive at the moment, so i bought an ebay Sharan VR6 anlage i can make fit. Lots of length, 55mm diameter, nice round mufflers and damn cheap. Doesn't have to last decades anyways.. ordered on wednesday, got here today already!  Last edited by Marcski : 02-11-2012 at 11:22.
|
|
#63
28-04-2011, 22:20
|
||||
|
||||
|
Engine bay is pretty solid underneath the dirt and grime;
 still gotta weld the corners behind the struts and some small holes, and it's ready for fresh paint Last edited by Marcski : 02-11-2012 at 11:23.
|
|
#65
28-04-2011, 22:58
|
||||
|
||||
|
International, Rene
|
|
#66
28-04-2011, 23:00
|
||||
|
||||
|
Nice work!
|
|
#67
15-06-2011, 08:03
|
||||
|
||||
|
mocked up, abf rail is a tight fit
 Last edited by Marcski : 02-11-2012 at 11:26.
|
|
#68
15-06-2011, 21:45
|
||||
|
||||
|
Pictures, or it didn't happen
|
|
#69
15-06-2011, 21:53
|
||||
|
||||
|
yeah where did the pic go
__________________
Insta: @knarfmk1 @085mk1gearboxmount Project lightweight  Te koop: Custom versnellingsbaksteun om een (085-) 5-bak in je 1100/1300 golf 1 te bouwen
|
|
#71
15-06-2011, 23:17
|
||||
|
||||
|
Nice!
|
|
#72
16-06-2011, 09:30
|
||||
|
||||
|
oops
|
|
#73
16-06-2011, 18:43
|
||||
|
||||
 finally got the MTX-L wideband in and sourced a nice front bumper Last edited by Marcski : 02-11-2012 at 11:27.
|
|
#74
22-06-2011, 22:06
|
||||
|
||||
|
i just had to try out the wideband
  Last edited by Marcski : 02-11-2012 at 11:27.
|
|
#75
22-06-2011, 22:14
|
||||
|
||||
|
Ha ha ... now you know your bike is running ok!
__________________
Oliecrisis....?? Gelukkig rijden onze auto's op accijns! ------------------------------------------- Weber Society Drenthe ® Last edited by J-9A-N : 23-06-2011 at 09:30.
|
|
#76
23-06-2011, 09:21
|
||||
|
||||
|
Actually it wasn't. Engine was cold and lots of fresh air because i couldn't hold it in but behind, so the reading was changing all the time. At least i know the controller is fast
|
|
#78
10-08-2011, 08:40
|
||||
|
||||
|
bought a new welder and was repairing rusty spots in the enginebay, but slow progress, because i'm busy working on the new website
|
|
#79
16-09-2011, 07:41
|
|||
|
|||
|
Quote:
Can you tell me from what bike this throttle bodies are and what diameter they have? Mark
|
|
#80
16-09-2011, 12:43
|
||||
|
||||
|
if i remember correctly, '01 GSX750R, tapered from 48 to 42mm at the butterfly
|
Linear Mode
