|
|
#301
18-09-2009, 18:55
|
|||
|
|||
Quote:
Stufffing the carbs with blue cheese is not a break in procedure Paul. Keep the carbs from ingesting cheese and they should be fine. 
|
|
#302
18-09-2009, 22:01
|
||||
|
||||
|
fuck this shit
__________________
no new friends
|
|
#303
19-09-2009, 01:42
|
||||
|
||||
|
well i didnt get my carbs tuned tonight............fuel all over the place... plugs were wet Tom..........
finally got my H&R ultra ultra lows on - here she sits with a bit of windage to go... I am also happy to say that after 20+ sets of wheels and hours of researching I got my stance SPOT ON. You will have to wait for those pics  
__________________
no new friends
|
|
#304
19-09-2009, 02:45
|
|||
|
|||
|
Quote:
screw pics, i wanna see that stance at h2o 
|
|
#306
19-09-2009, 09:11
|
||||
|
||||
|
" Float level, in mm, typically refers to the distance from the face of the carburetor top cover to the float. With the top cover held vertically (float pivot at the top) and the float tab (Lc) resting against, but not depressing the spring loaded ball in the needle valve, measure between the face of the carburetor top cover to the top or bottom of the float. On carburetor models where it is required to remove the float to replace the top cover gasket, the measurement should be made with the gasket in place to the gasket face."
why does this sound like fucking eskimo?? if the float level is resting against, but not depressing the spring loaded ball in the needle valve, why do you need to measure?? ok Paul shutup and stop overthinking this.........  ...then I see the little side note at the bottom of the diagram and get more confused....  brass float only? specs may vary? Plastic float height 12.5mm to tip of float? OK I know I have plastic floats...........I DONT HAVE BRASS. Is this just another example of me chasing my tail & getting NOWHERE at the end? I THINK SO    WTF!  
__________________
no new friends Last edited by Chromosexual : 19-09-2009 at 09:23.
|
|
#307
19-09-2009, 09:32
|
||||
|
||||
|
As I felt that maybe these diagrams were a little cryptic, I decided to look elsewhere for more info..........and it got more confusing!!! same carb.............diff float height..... WTF?!?!
__________________
no new friends
|
|
#308
19-09-2009, 15:07
|
||||
|
||||
|
sorry mang, but what don't you understand? just set it to like 12.5ish
when the float raises in the carb it will hit the ball on the valve. measure the distance. when the valve is depressed by the rising float, measure the distance. if the first of the two is off, bend the tab slightly to set it correctly. easypeasylemonsqueezy.
__________________
79 golf gti wannabe.
|
|
#310
19-09-2009, 17:27
|
||||
|
||||
  
__________________
no new friends
|
|
#311
20-09-2009, 00:37
|
||||
|
||||
|
Quote:
and sir..............you will be seeing her 
__________________
no new friends
|
|
#312
20-09-2009, 02:43
|
|||
|
|||
|
Quote:
great to hear man!!!!!!!!!!!
|
|
#313
20-09-2009, 03:46
|
||||
|
||||
|
yeah i redid the cams (again)
the biggest bitch today was the syncing of the carbs the floats (BTW) were a bit off........ the idle screw linkage setup was a little diff that the other setup I had so I really had to crank down that idle screw to get it where I could sync them. I feel bad that I turned down Ariel (owner of Perfect Metal Finishing) to get together tomorrow to detail the fuuuukk out of the 78 but she is running so poorly (took her for a spin a few mins ago - lean all out) that I didnt feel comfortable with him polishing my turd the way it was. Hopefully things will go better tomorrow...and I cant actually focus on aesthetics like I always do.......pfft
__________________
no new friends
|
|
#314
20-09-2009, 20:22
|
||||
|
||||
|
ahhhhhhhhhhh so fucking sweet
still a bit lean ..... but OMG I got her up to 4th gear and WOW!!! now i gotta clean her up .................. WAAAAH 
__________________
no new friends
|
|
#316
20-09-2009, 22:01
|
||||
|
||||
|
Ariel is coming along with me
I might just Quilmes myself :o 
__________________
no new friends
|
|
#317
20-09-2009, 22:41
|
|||
|
|||
|
sweeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeet
you showing?
|
|
#319
20-09-2009, 23:48
|
|||
|
|||
|
Quote:
Should I bring stuff for chroming?
|
|
#320
21-09-2009, 00:18
|
||||
|
||||
|
Quote:
oh si  Quote:
your call senior......  Quote:
fixed  ...and yes I registered a few days back....maybe last tuesday or so
__________________
no new friends
|
Linear Mode
